~Toughbooktalk~ Rob - 630-300-8877

The largest Toughbook discussion site on the net!
It is currently Wed Nov 14, 2018 8:57 pm

All times are UTC-06:00




Post new topic  Reply to topic  [ 3 posts ] 
Author Message
 Post subject: Recommendations on OS
PostPosted: Tue Aug 28, 2012 6:34 am 
Ok so I ended up getting a MK5. I swapped my components out of my my MK3, to get the BLUE SCREEN OF DEATH :blowaway: :doh: After investigationg out the issue, I come to find out I need to reinstall the OS. Simple enough usually... The cruel joke is I do not have my old copy of Win XP Pro SP1 laying around. This however gives me a few options.

I can either:
    1) Buy a copy of Win XP Pro SP2
    2) Buy a copy of Win 7 Premium or Win 7 Pro
    3) Download a copy of Ubuntu

This leads me to a few questions however:
    1) I haven't figured out weather or not the CF-29 use 32 or 64 bit OS, or if it matters which one.
      1a) Which would be recommended?
    2) Is there any benifit to running Win 7?
      2a) There again 32 or 64 bit.
      2b) Win 7 Premium or Win 7 Pro?
    3) What is the combatability of Ubuntu with existing software? i.e. MS Office etc?

Where can I locate a Recovery Disk or download a recovery disk for my model: CF-29NTQGZBM

Thanks in advance.


Grim


Top
   
PostPosted: Tue Aug 28, 2012 7:56 am 
Offline
User avatar

Joined: Tue Dec 21, 2010 12:51 pm
Posts: 1884
Location: Northeast Louisiana
The CF-29's use a Pentium M, that is a 32 bit only processor.

Personally I dual booted XP with Ubuntu. If you use Linux and want to run windows programs you will need WINE. Ubuntu comes with open office a windows office alternative. Ubuntu 10.10 worked really well I haven't really tried any of the newer versions on it.
http://forum.notebookreview.com/panason ... rsion.html

Windows 7 will work but will use more resources to run than XP unless you tweak it, that goes for drivers as well.

I am sure someone can point you in the right direction for restore disks. If now do you have anyother OEM restore disks lying around?

The BSOD was caused by chip-set being different this model uses DDR2 ram, an upgrade from Mk3 and older DDR ram. You could try un-installing the chipset driver and other specific drivers that deal with cpu, etc. Then when windows start looking quickly power off and swap to the newer CF-29. Intel 855GME Mk3 vs Intel 915GMS on the and video. I have had this work on some pc's since you are still using a Pentium M in the same family. When too much hardware changes windows anti-piracy kicks in and BSOD.

_________________
CF-28 MK2,Mk3 / CF-29 Mk3 / CF-30 MK2 / CF-25 Mk1 ATI / CF-19 MK3/Mk3/Mk5 / CF-U1 Mk1,Mk2 / CF-M34 Mk7/Mk3 / CF-17 Mk1 / CF-07
Voodoo Envy M355 / M360 / M515 / M780 / U703 / Voodoo Hexx / Voodoo Idol / Voodoo Rage F1 / Voodoo Rage F1 / Voodoo Rage F1 "signed case" / Voodoo Omen
Alienware M11x R1


Top
   
PostPosted: Wed Aug 29, 2012 2:20 pm 
Offline
User avatar

Joined: Sat Aug 18, 2012 4:01 pm
Posts: 11
restore disks available on eBay for around $40

do you have a COA on the bottom for XP? that may mean you don't have to pay again and just find an XP Pro SP2 disk from someone, load it up, use your COA and then download the drivers from the panasonic web site (free)

that's the cheapest route - $0 if you have the COA and can find a XP cdrom

it does take a little work to get each driver properly installed manually, but it's not too hard

Windows 7 works pretty good, I would suggest Windows 7 Professional, I really doubt you need ulitmate. It too is not too hard to get going, but you need to download the Vista upgrade drivers from the panasonic web site and manually install those too. You can find Windows 7 Pro for around $99 a copy

that's the benefit if the real restore CDs, you don't have to mess with getting the drivers right

I would imagine getting all the drivers working is even harder with linux - I am sure you can get most of them working good enuf with some work

hope that helps. I have a CF-29 running XP Pro, one running Windows 7 ultimate, one running Windows 7 Pro, and one running Windows 8 pre-release. they all work good!


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 3 posts ] 

All times are UTC-06:00


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited