~Toughbooktalk~

Posted: **Sun Apr 19, 2015 6:44 pm**

I still think the touchscreen is failing....Windows may be more forgiving....

Posted: **Mon Apr 20, 2015 9:06 am**

I am going to run it with W7 until it dies, then I will change it out.

Thanks to everyone for the ideas/suggestions.

Posted: **Mon Apr 20, 2015 8:28 pm**

I had a post or two written and got de-railed as it were, only to come back and see half a message sitting there. Too late, too tired, too lazy I would shut down.

I am interested in your mint numbers from xinput calibrate.

This 74 (lovingly named Crash) I ran the calibrator as a touch and as a tablet. As a touch the numbers are bigger. However the smaller numbers are way small.......identifying the bad circuit/trace.

Point being calibrator will tell you which trace is bad.

Posted: **Tue Apr 21, 2015 8:03 am**

Here is my 99-calibration.conf:

Code: Select all

Section "InputClass"
	Identifier	"calibration"
	MatchProduct	"Fujitsu Component USB Touch Panel"
	Option	"Calibration"	"235 3911 306 4017"
	Option	"SwapAxes"	"0"
	Option "EmulateThirdButton"  "1"
	Option "EmulateThirdButtonMoveThreshold" "50"
EndSection

I will fire up the 29MK4, with a very good working TS, and see how the numbers compare.

Posted: **Tue Apr 21, 2015 8:09 am**

And here is the 99-calibration.conf from the 29MK4 running MX-14:

Code: Select all

Section "InputClass"
	Identifier	"calibration"
	MatchProduct	"LBPS/2 Fujitsu Lifebook TouchScreen"
	Option	"Calibration"	"272 3984 316 3854"
	Option "EmulateThirdButton"  "1"
	Option "EmulateThirdButtonMoveThreshold" "50"
EndSection

The numbers look close to me.

Posted: **Tue Apr 21, 2015 1:04 pm**

How about setting bios to "touchscreen" and checking those numbers.

CF-74 This is a known bad screen on a burnt lcd. Good ol' Crash. The bottom x's won't work with a stylus so I used the touchpad.

Doing dynamic recalibration:
Setting calibration data: 57, 16366, 16, 16356
--> Making the calibration permanent <--
copy the snippet below into '/etc/X11/xorg.conf.d/99-calibration.conf' (/usr/share/X11/xorg.conf.d/ in some distro's)
Section "InputClass"
Identifier "calibration"
MatchProduct "Fujitsu Component USB Touch Panel"
Option "Calibration" "57 16366 16 16356"
Option "SwapAxes" "0"

Just an obvious sample....nothing more.

Posted: **Tue Apr 21, 2015 3:07 pm**

It was dumb...I deleted it...

Posted: **Wed Apr 22, 2015 8:51 am**

I set the BIOS to 'Touchscreen' and then ran the calibrator. Here are the numbers:

Code: Select all

Section "InputClass"
	Identifier	"calibration"
	MatchProduct	"Fujitsu Component USB Touch Panel"
	Option	"Calibration"	"2563 4547 2874 4572"
	Option	"SwapAxes"	"0"
EndSection

Even though it completed the calibration, the cursor goes to the bottom right corner of the screen. During calibration there were many 'mis-click' errors with the cursor going to the right side of the screen before it completed.

Posted: **Wed Apr 22, 2015 5:58 pm**

I installed Makulu, xinput calibrator and here are the numbers:

Code: Select all

Section "InputClass"
	Identifier	"calibration"
	MatchProduct	"Fujitsu Component USB Touch Panel"
	Option	"Calibration"	"246 3907 314 4043"
	Option	"SwapAxes"	"0"
	Option "EmulateThirdButton"  "1"
	Option "EmulateThirdButtonMoveThreshold" "50"
EndSection

They all look normal, except when set to 'Touchscreen' in BIOS.
I will have to use Makulu some before I decide if the TS works better, worse or the same as in Mint, first impressions....it might be working a bit better (less pressure before cursor moves).

Posted: **Wed Apr 22, 2015 9:08 pm**

Curiosity only on TS. Tablet numbers look pretty good.

Have you played with threshold numbers at all....the 50?

My CF-31 matches pretty close the numbers you had w/TS. It prefers tablet.

I have a bad mobo CF-30 MK3.

~Toughbooktalk~

CF-30KCPAXAM - Top inch of TS very unresponsive

Re: CF-30KCPAXAM - Top inch of TS very unresponsive

Re: CF-30KCPAXAM - Top inch of TS very unresponsive

Re: CF-30KCPAXAM - Top inch of TS very unresponsive

Re: CF-30KCPAXAM - Top inch of TS very unresponsive

Re: CF-30KCPAXAM - Top inch of TS very unresponsive

Re: CF-30KCPAXAM - Top inch of TS very unresponsive

Re: CF-30KCPAXAM - Top inch of TS very unresponsive

Re: CF-30KCPAXAM - Top inch of TS very unresponsive

Re: CF-30KCPAXAM - Top inch of TS very unresponsive

Re: CF-30KCPAXAM - Top inch of TS very unresponsive